- Single exhaust consists of the Y pipe, rear exhaust pipe, muffler, and tailpipe.
- You will be asked report with or without hot air heater in the check out process.
- 1940-48 MY's with the hot air heater will need to report the OD at the manifold.
-
This listing covers model years 1936, 1937, 1938, 1939, 1940, 1941, 1942, 1943, 1944, 1945, 1946, 1947, and 1948 Lincoln Continentals with the stock V12. Photo depicts the system for 1940-48 Continentals stock with the V12 and a Hot Air Heater -
This listing covers model years 1936, 1937, 1938, 1939, 1940, 1941, 1942, 1943, 1944, 1945, 1946, 1947, and 1948 Buick's with a straight 8. This listing is for MY's 1941-46 Buick's stock with a single carburetor set up. If your 1941-46 Buick was stock with a dual carburetor set-up refer to listing 568792. Photo depicts the system for a 1938 Buick 40 Series Special.- For MY's 1936-39 this single exhaust system consists of exhaust pipe, muffler, and tailpipe.
- For MY's 1940-48 this single exhaust system consists of the front exhaust pipe, rear exhaust pipe, muffler, and tailpipe.
-
This listing covers model years 1936, 1937, 1938, 1939 & 1940 Nash Lafayette with a L-HE flathead 6. Photo depicts the single exhaust for 1940 Nash Lafayette with the stock L-Head 6cyl engine.- Single exhaust system consists of the exhaust pipe, muffler and tailpipe.
- This application does not have an exhaust manifold. The exhaust pipe serves as the manifold and clamps directly to the cylinder head. Waldron's Exhaust does not carry the needed clamps.
-
This listing covers model years 1936, 1937, 1938, 1939, and 1940 Cadillac's with stock single exhaust with 2 mufflers. Excludes Model 65 as we do not have patterns. Photo depicts the system for a 1937 Cadillac 70 Series.- For Model's 60, 60S, 70 & 75 this system consists of the front exhaust pipe, rear exhaust pipe, front muffler, over-axle pipe, rear transverse muffler w/long inlet pipe, tailpipe and bracket.
-
This listing covers 1936 & 1937 GMC ½T trucks with the stock Olds 213ci 6 cyl. Photo shows the stock single exhaust system for 1936-37 GMC ½T's with the Olds 213ci where the muffler sits outside the frame rail.- Single exhaust system consists of the exhaust pipe, muffler, and tailpipe.
- Waldron's does not have the gaskets available for this system.
- In the ordering process, you will be asked to report where the muffler sits on your system (inside or outside of the frame rail),
-
- This single exhaust system consists of the exhaust pipe (w/2 bolt flange), front muffler, connector pipe, and tailpipe with rear muffler built into the inlet end.
-
Listing covers model years 1936, 1937, 1938, 1939, 1940, 1941, 1942, 1943, 1944, 1945, 1946, 1947, 1948, 1949, 1950, 1951, 1952, and 1953 Fords passenger cars with the stock flathead V8 with stock manifolds. This listing is not for Ford trucks. See listing 453292 for 1935-41 Ford ½T's & 453293 for 1948-52 F1-F3's dual conversion kits. Convert your flathead Ford to a dual exhaust with Waldron's Dual Conversion Kits! This dual conversion kit bolts directly to the stock manifolds (only). Conversion kit consists exhaust pipes, glasspacks, and tailpipes, along with gaskets and clamps. 1949-53 model years will also receive a blocker plate. Hangers are not included. Photos depicts the system for MY's 1949-53.- 1935-38; LS front & rear exhaust pipes start out at 1½" then bump up to 1 7/8" at the glasspacks, RS exhaust pipe is 1 7/8" with LS/RS tailpipes at 1½".
- 1939-41; LS front & rear exhaust pipes start out at 1½" then bump up to 1 7/8" at the glasspacks, RS exhaust pipe is 1 7/8" with LS/RS tailpipes at 1 5/8".
- 1942-48; LS front & rear exhaust pipes start out at 1½" then bump up to 1 7/8" at the glasspacks, RS exhaust pipe is 1 7/8" with LS/RS tailpipes at 1¾".
- 1949-53; LS front & rear exhaust pipes start out at 1½" then bump up to 2" at the glasspacks, RS exhaust pipe is 2" with LS/RS tailpipes at 1¾".
- 1949-51 with rear exit DS manifold; LS exhaust pipe starts out at 1 5/8" then bump up to 2" at the glasspacks, RS exhaust pipe is 2" with LS/RS tailpipes at 1¾".
-
This listing covers MY's 1935, 1936, 1937, 1938, 1939, 1940, 1941, 1942, 1943, 1944, 1945, 1946, 1947, and 1948 Ford's with their respective stock flathead V8. Photos depicts the single exhaust system for a 1939 Ford Coupe without the heat exchanger (where customer opted to have tailpipes cut to reduce the cost of shipping).- For MY's 1935-36 & 1941-48 this single exhaust system consists of the crossover pipe, Y pipe, muffler, and tailpipe.
- For MY's 1937-40: If your 1937-40 Ford has the heat exchanger & you intend to reuse it; the system will consist of a cross-over pipe, exhaust pipe, muffler & tailpipe. If your 1937-40 doesn't have the heat exchanger or if it does have it but it is not reusable; the system will consist the 2 pc. Y pipe (AKA cross-over & Y pipe), muffler & tailpipe. You will be asked to report which setup you require in the check out process.
-
This listing covers model years 1935, 1936, 1937, 1938, 1939, 1940, 0941, 1942, 1943, 1944, 1945, 1946, and 1947 F1, F2, and F3's with the stock 4 cyl or 6 cyl engine. Photo shown is generic and is posted so that you might see the quality of our craftsmanship and the type of bending.- Single exhaust system consists of exhaust pipe, muffler and tailpipe.
-
Listing covers MY's 1935, 1936, 1937, 1938, 1939, 1940, and 1941 Ford ½T Trucks with the stock flathead V8. Convert your flathead Ford to dual exhaust with Waldron's exclusive Dual Conversion kits! Complete kit bolts on to the stock manifolds. Not available for 1933-34, 1942-47 or 1953 MY's.
- Dual conversion kit consists of the exhaust pipes, custom-built glasspacks, tailpipes, blocker plate, gaskets and clamps. Gaskets & steel clamps are included. After 1949, the RS exhaust requires blocking plate which will be included in the system. Universal hangers can be added to the cart, if needed. Period specific hangers are N/A.
- The system goes through existing holes in the crossmembers. LH exhaust pipe starts at 1 ½”OD and opens to 2”OD at the glasspack inlet. RH exhaust pipe 2” OD throughout. Tailpipes are either 1 5/8” or 1 ¾” depending on the material selected & MY.
- If you would prefer mufflers (over glasspacks), you may make that change to your order in the check out process. Additional cost of $115.00 for aluminized steel or $230.00 for T409 SS.
-
This listing covers model years 1935, 1936, 1937, 1938, 1939, 1940, and 1941 Ford ½T's with the stock flathead V8. Photo depicts the stock single exhaust for 1940 Ford ½T trucks with the stock 239ci flathead V8.- Single exhaust consists of the crossover pipe, Y pipe, muffler, and tailpipe.
-
This listing covers MY's 1935, 1936, and 1937 Ford 1½T's trucks with the stock V8. Photo depicts the stock single exhaust for 1936 Ford 1½T trucks with the stock 221ci V8 4WD 157"WB where customer selected option 2 on the flange rotation.- Single exhaust system consists of the crossover pipe, exhaust pipe, muffler, and tailpipe. You will be ask to report the flange rotation in the check out process.