- Single exhaust system consists of the Y pipe, rear exhaust pipe, muffler, over-axle pipe, and resonator eliminator pipe (integral resonator with rectangular polished stainless steel outlet has been eliminated).
- Waldron's Exhaust does not offer over-sizing on this system. Y pipe starts off the manifolds at 1&7/8"OD and increases to 2½"OD where the Y pipe comes together, rear exhaust pipe is 2½"OD and reduces to 2¼"going into the muffler and stays 2¼" through remainder of system.
-
This listing covers MY's 1965 and 1966 Dodge Darts stock with the 273ci V8 and 4 BBL carburetor. Due to our manufacture loosing our pattern for the special tip, our last shipment of this part was not up to our standards and this listing no longer includes the special resonator. If you would like to see what we can offer regarding this resonator, please refer to SKU Arvin1212. Photo is correct to the listing. -
This listing covers model years 1967, 1968, 1969, 1970, 1971, 1972, 1973, and 1974 GTS, Swinger, and Dart's V8 (except 273ci or 318ci) stock with a dual exhaust with 2 mufflers. Photo depicts the system for a 1968 Dart with the stock 340ci.- Dual exhaust system consists of LS/RS exhaust pipes, LS/RS mufflers, and LS/RS tailpipes.
-
This listing covers model years 1970, 1971, 1972, 1973, and 1974 Challenger's with the stock 340ci, 383ci, or 440ci and the stock dual exhaust system with mufflers and resonators. Excludes 426ci engine since that system requires an H pipe. Photo depicts the system for 1970-71 Dodge Challenger's stock with the 440ci and 3-2 bbl carburetor set-up.- Dual exhaust system consists of LS/RS exhaust pipes, LS/RS resonators, LS/RS connector pipes, and LS/RS mufflers w/tailspout (only certain set-ups). Some systems (depending on engine and carburetor setup) were stock with chrome tips which are NOT part of this system.
-
This listing covers model years 1970, 1971, 1972, 1973, and 1974 Challengers. Photo shown is generic and is posted so that you might see the quality of our craftsmanship and the type of bending.- Single exhaust system consists of Y pipe, rear exhaust pipe, muffler and tailpipe. Y pipe may be NORS.
-
This listing covers model years 1973, 1974, 1975, and 1976 Dart's with the stock 6 cyl engine and stock with a resonator. Some 1972 Dodge Challengers were stock with resonators but the exhaust pipe for that system has never been reproduce so until we procure that pipe, the complete system is unavailable.- Single exhaust consists of the exhaust pipe, muffler, over-axle pipe, and resonator with tailpipe.
-
This listing covers model years 1928, 1929, 1930, 1931, and 1930 Durant's. Photo shown is generic and is posted so that you might see the quality of our craftsmanship and the type of bending.- Single exhaust consists of exhaust pipe, muffler, and tailpipe.
- On MY's 1928 & 1929 the exhaust pipe will come without a flange and without a flare.
-
This listing is for all 1958 Pacers, Rangers, Citations, Corsairs, Round Up, Bermuda, and Villager's with the stock V8 and dual exhaust. Photo depicts the system for 1958 Edsel Corsair & Citation HT's.- Dual exhaust systems for 1958 Pacer or Ranger Station Wagon's consists of LS/RS exhaust pipes, LS/RS mufflers, LS/RS connector pipes, and LS/RS resonators with tailspout. All others body styles with dual exhaust consist of LS/RS exhaust pipes, LS/RS mufflers, LS/RS front tailpipes with 5" round resonator's built in, and LS/RS rear tailpipe. These systems are stock at 2"OD through out.
- Dual exhaust systems for 1958 Corsair or Citation consists of LS/RS exhaust pipes, balance tube, LS/RS mufflers, LS/RS connector pipes, and LS/RS resonators with tailspout.
-
This listing is for all 1958 Pacer, Ranger, Citation & Corsair's with the stock V8 and single exhaust, including convertibles. Photo is correct to the listing.- Single exhaust consists of the Y pipe, muffler, front tailpipe with resonator, and rear tailpipe.
-
This listing is for all body styles 1959 Pacer, Ranger, Citation, and Corsair's with the stock V8 and dual exhaust. Photo depicts the exhaust system for 1959 Edsel's, except convertibles and station wagons.- Dual exhaust system consists of LS/RS exhaust pipes, LS/RS mufflers, LS/RS front tailpipes and LS/RS rear tailpipes. From the factory, these tailpipes were all in 1 piece but are so long that they must be reproduced in 2 sections.
-
This listing covers 1959 & 1960 Edsel's (exc. 1960 convertible) with the stock 6 cyl. Photo shown is generic and is posted so that you might see the quality of our craftsmanship and the type of bending.- For MY 1959 the single exhaust consists of the exhaust pipe, muffler, and tailpipe. Listing covers all body styles.
- For MY 1960 the single exhaust consists of the front exhaust pipe, rear exhaust pipe, and muffler with tailpipe. Listing excludes Edsel convertibles.
-
This listing covers 1959 & 1960 Edsel Ranger, Corsair, & Villager Station Wagon's with the stock V8. Photo shown is generic and is posted so that you might see the quality of our craftsmanship and the type of bending.- For MY 1959 the single exhaust system consists of the Y pipe, muffler and tailpipe.
- For MY 1960 the single exhaust system consists of the Y pipe, rear exhaust pipe, and muffler with tailpipe.
-
This listing covers 1960 Edsel's with the stock V8 332ci & 361ci. The 292ci V8 was stock with a single exhaust (only). Listing excludes Ranger convertibles. Photo shown is generic and is posted so that you might see the quality of our craftsmanship and the type of bending.- Dual exhaust consists of H pipe, LS/RS mufflers, and LS/RS tailpipes.
-
AFTERMARKET NOS PARTS FROM WALDRON'S EXHAUST; These are components that we have acquired over the years. The parts were manufactured by Walker, Maremont, International Parts Corp (IPC), Arvin or other exhaust component manufacturers as service replacement parts for OEM components. They will be cleaned to remove any surface corrosion and coated with a corrosion-resistant coating unless you ask us to leave them untreated. This pipe fits 1967 Buick Skylark Sport Wagon V8 with Super Turbine 400 trans. This part will generally ship within 1 wk. -
AFTERMARKET NOS PARTS FROM WALDRON'S EXHAUST; These are components that we have acquired over the years. The parts were manufactured by Walker, Maremont, International Parts Corp (IPC), Arvin or other exhaust component manufacturers as service replacement parts for OEM components. They will be cleaned to remove any surface corrosion and coated with a corrosion-resistant coating unless you ask us to leave them untreated. This Y pipe fits 1971-73 Ford Mustang / Mercury Cougar with 351ci engine. This part will generally ship within 1 wk. -
AFTERMARKET NOS PARTS FROM WALDRON'S EXHAUST; These are components that we have acquired over the years. The parts were manufactured by Walker, Maremont, International Parts Corp (IPC), Arvin or other exhaust component manufacturers as service replacement parts for OEM components. They will be cleaned to remove any surface corrosion and coated with a corrosion-resistant coating unless you ask us to leave them untreated. This Y pipe fits 1973 Buick Century, LeSabre, Centurion with 350ci engine. This part will generally ship within 1 wk. -
AFTERMARKET NOS PARTS FROM WALDRON'S EXHAUST; These are components that we have acquired over the years. The parts were manufactured by Walker, Maremont, International Parts Corp (IPC), Arvin or other exhaust component manufacturers as service replacement parts for OEM components. They will be cleaned to remove any surface corrosion and coated with a corrosion-resistant coating unless you ask us to leave them untreated. This Y pipe fits 1975-76 Chevrolet 400 & 350 engines w/ 2bbl carburetor. Excludes models w/ A.I.R. This part will generally ship within 1 wk. -
AFTERMARKET NOS PARTS FROM WALDRON'S EXHAUST; These are components that we have acquired over the years. The parts were manufactured by Walker, Maremont, International Parts Corp (IPC), Arvin or other exhaust component manufacturers as service replacement parts for OEM components. They will be cleaned to remove any surface corrosion and coated with a corrosion-resistant coating unless you ask us to leave them untreated. This Y pipe fits Chevrolet Full Size V8; 1968 w/396ci, 1969 w/396ci & 427ci, 1970 w/454ci. This part will generally ship within 1 wk. -
This listing covers model years 1909, 1910, 1911, 1912, 1913, 1914, 1915, 1916, 1917, 1918, 1919, 1920, 1921, 1922, 1923, 1924, 1925, 1926, and 1927 Model T's. Photo is correct to the listing.- Consists of exhaust pipe and muffler.
- Exhaust pipe does not take a flange, it has a flare that uses a special nut which is not provided.
-
This listing covers model years 1928, 1929, 1930, and 1931 Model A's. Photo depicted is correct to the listing.- This is a one piece unit and consists of the exhaust pipe, tapered muffler and tailpipe. Available in aluminized steel, only.
- Exhaust pipes does not take a flange, it has a flare that uses a special nut which is not provided.
- Refer to eBay for the copper gasket that is required.
-
This listing covers model years 1932, 1933, and 1934 Ford's with their respective stock flathead V8 with single exhaust. Photo depicts the single exhaust for 1933-34 Ford's with the stock flathead V8.- This single exhaust system consists of the crossover pipe, Y pipe, muffler, front tailpipe and rear tailpipe. The stock design takes the tailpipe through the rear cross-member.
-
Photo depicts the system for manifolds with 45° angle- Single exhaust consists of exhaust pipe, muffler, front tailpipe and rear tailpipe.
- You will be asked to report manifold exit in the ordering process.
-
Listing covers model years 1936, 1937, 1938, 1939, 1940, 1941, 1942, 1943, 1944, 1945, 1946, 1947, 1948, 1949, 1950, 1951, 1952, and 1953 Fords passenger cars with the stock flathead V8 with stock manifolds. This listing is not for Ford trucks. See listing 453292 for 1935-41 Ford ½T's & 453293 for 1948-52 F1-F3's dual conversion kits. Convert your flathead Ford to a dual exhaust with Waldron's Dual Conversion Kits! This dual conversion kit bolts directly to the stock manifolds (only). Conversion kit consists exhaust pipes, glasspacks, and tailpipes, along with gaskets and clamps. 1949-53 model years will also receive a blocker plate. Hangers are not included. Photos depicts the system for MY's 1949-53.- 1935-38; LS front & rear exhaust pipes start out at 1½" then bump up to 1 7/8" at the glasspacks, RS exhaust pipe is 1 7/8" with LS/RS tailpipes at 1½".
- 1939-41; LS front & rear exhaust pipes start out at 1½" then bump up to 1 7/8" at the glasspacks, RS exhaust pipe is 1 7/8" with LS/RS tailpipes at 1 5/8".
- 1942-48; LS front & rear exhaust pipes start out at 1½" then bump up to 1 7/8" at the glasspacks, RS exhaust pipe is 1 7/8" with LS/RS tailpipes at 1¾".
- 1949-53; LS front & rear exhaust pipes start out at 1½" then bump up to 2" at the glasspacks, RS exhaust pipe is 2" with LS/RS tailpipes at 1¾".
- 1949-51 with rear exit DS manifold; LS exhaust pipe starts out at 1 5/8" then bump up to 2" at the glasspacks, RS exhaust pipe is 2" with LS/RS tailpipes at 1¾".
-
This listing is currently for a 1960 Edsel convertible with a 352ci. We do not have the exhaust pipe patterns needed for the 292ci.
- Dual exhaust consists of LS has front exhaust pipe, resonator, connector pipe, and muffler with tailpipe while RS has front exhaust pipe, rear exhaust pipe and muffler with tailpipe. No resonator on the RS.
-
This listing covers model years 1949, 1950, 1951, 1952, 1953, 1954, 1955, and 1956 Ford Mainline, Customline, and Crestline's stock with the flathead V8. Photo depicts the system for MY's 1952-53 Ford's (except convertibles, SW's & sedan delivery's) with the tailpipe built in 2 sections for shipping purposes.- Single exhaust consists of the crossover pipe (MY's 1949-53 pipes crosses under the engine / MY's 1954-56 pipe crosses over the engine), exhaust pipe, muffler, and tailpipe.
-
This listing covers model years 1952,1953, 1954, 1955, and 1956 Ford's stock with a 6 cyl. Photo depicts the stock single exhaust for 1955-56 Ford Station Wagon's and Sedan Deliveries with the stock 6cyl.- Single exhaust consists of the exhaust pipe, muffler, and tailpipe.
-
This listing covers model years 1955, 1956, 1957, 1958, and 1959 Ford V8's stock with a dual exhaust. Excludes 1957-59 Convertibles & Retractable Hard Tops, for these systems refer to SKU: 518710. Photo depicts the system for MY's 1955-56 Ford Sunliner convertibles with the stock V8.- For 1955-56 MY's this dual exhaust system consists of LS/RS exhaust pipes, LS/RS mufflers, and LS/RS tailpipes.
- For 1957 S.W.'s, Ranchero's & Sedan Deliveries this dual exhaust system consists of LS/RS exhaust pipes, LS/RS mufflers, and LS/RS tailpipes. For all other body styles, this dual exhaust will consist of LS/RS exhaust pipes, LS/RS mufflers, LS/RS front tailpipes and LS/RS rear tailpipes.
- For 1958 & 1959 MY's this dual exhaust will consist of LS/RS exhaust pipes, LS/RS mufflers, LS/RS front tailpipes and LS/RS rear tailpipes.
-
This listing covers model years 1957, 1958, and 1959 Ford V8 with stock single exhaust except 1959 Convertibles or Retractable Hardtops. Photo depicts the stock single exhaust system for 1959 Ford Station Wagons and Ranchero's with the stock 332ci V8 (this customer opted to have the tailpipe "cut").- Single exhaust consists of the Y pipe, muffler, front and rear tailpipe (1 pc. from factory but due to 10'L tube restrictions, this tailpipe is reproduced in 2 pcs.). Except 1957 Convertibles & Retractable Hardtops which take a Y pipe, muffler, front and rear tailpipe. Y pipe may be NORS.
-
This listing covers model years 1957, 1958, and 1959 Ford's stock with a 6 cyl. Photos depicts the system for a 1957 Ford sedan with the stock 6 cyl. Tail pipe is built in 2 pcs. due to it exceeding a 10' pc. of tubing.- Single exhaust consists of exhaust pipe, muffler, front and rear tailpipe (1 pc. from factory/see above).
-
This listing covers model years 1957, 1958 and 1959 Ford retractable hardtop's and convertibles with the stock V8 and dual exhaust. For 1958 Convertibles, this is a resonator eliminator options. If you would like to keep your convertible stock with the resonators, please give us a call. Photo depicts the system for 1957 Skyliner Retractable Hard Tops with the stock V8.- Dual exhaust system consists of LS/RS front exhaust pipes, mufflers, LS/RS front tailpipe, and LS/RS rear tailpipes.
- The front and rear tailpipe sections are different between a Retractable Hard Top and a soft-top Convertible. Please report the body-style appropriately.
-
This listing covers MY's 1960 and 1961 Ford Sunliner convertibles.
- For 1960 models this dual exhaust consists of LS front exhaust pipe, LS resonator, LS rear exhaust pipe and LS muffler with tailspout while the RS will have a front exhaust pipe, rear exhaust pipe, and muffler with tailspout.
- For 1961 models this dual exhaust consists of LS front exhaust pipe, LS resonator, LS rear exhaust pipe, and LS muffler with tailspout while the RS consists of a long exhaust pipe and RS muffler with tailspout.
-
This listing covers 1960 and 1961 Fairlane's, for 1962 and up refer to Ford Mid Size listings. Also covers 1960, 1961, 1962, 1963, and 1964 Galaxie, Starliner, and Custom's with the stock V8 and a single exhaust. Photo shown is generic and is posted so that you might see the quality of our craftsmanship and the type of bending.- Single exhaust system consist of the Y pipe, rear exhaust pipe, and muffler with tailpipe. Y pipe may be NORS.
-
This listing covers model years 1960, and 1961 Fairlane's (for 1962 and up refer to Ford Mid Size) 1960, 1961, 1962, 1963, and 1964 Galaxie, Starliner, 300's and Custom's with the stock V8 and dual exhaust, except Sunliner convertibles. For MY's 1960-61 Sunliner's, refer to listing 518711. For MY's 1962-64 Sunliner's, refer to listing 518716. Photo depicts the stock dual exhaust for 1963 Full Size with a 406ci or 427ci with long branch manifolds.
- This dual exhaust system consists of the H pipe, LS/RS rear exhaust pipe, and LS/RS mufflers with tailpipe.
-
This listing covers model years 1960, 1961, 1962, 1963, and 1964 Sunliner convertibles.
- Single exhaust consists of the exhaust pipe, resonator, connector pipe, and muffler with tailpipes.
-
This listing covers model years 1960 and 1961 Fairlane's (for 1962 & up refer to Ford Mid Size), 1960, 1962, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, and 1974 Galaxie, Starliner, and Custom's with a stock 6 cyl. Photo depicts the stock single exhaust for 1968 Full Size Ford's with the stock 240ci 6 cyl, except SW's.- Single exhaust consists of the exhaust pipe, muffler, and tailpipe.
-
This listing covers MY's 1962, 1963 and 1964 Ford Sunliner, Galaxie, 300 & Custom convertibles. Photo depicts the dual exhaust system for 1964 Ford Full Size Convertibles with the stock 390ci and log style manifolds.- Dual exhaust system consists of LS/RS exhaust pipes, LS/RS resonators, LS/RS connector pipes, LS/RS muffler with tailpipes.
-
This listing covers model years 1965, 1966, 1967, 1968, 1969, and 1970 Ford Custom, LTD, and Galaxies with the stock V8 and dual exhaust. Includes convertibles and station wagon's. Excludes 1966 and 1967 7 Liter systems. Photo depicts the system for a 1966 Galaxie with the stock 352ci.- For all model years but 1965 SW this dual exhaust consists of the H pipe, LS/RS mufflers, LS/RS front tailpipes, and LS/RS rear tailpipes. Tailpipe were 1 piece from the factory but come in 2 pieces in reproduction. H pipe may be NORS.
- 1965 full size station wagon has the H pipe, LS/RS mufflers, LS front, center and rear tailpipes and RS front and rear tailpipes. H pipe may be NORS.