- MY's 1960-65: system consists of the front exhaust pipe, rear exhaust pipe, and muffler w/tailspout.
- MY 1966: system consists of the front exhaust pipe, rear exhaust pipe (turns in board), and transverse muffler w/tailspout.
- MY's 1967 & 1969-70: system consists of the front exhaust pipe, rear exhaust pipe, muffler, and tailpipe.
- MY 1968: system consists of the front exhaust pipe, rear exhaust pipe w/muffler, and tailpipe.
- MY's 1971-74: system consists of the front exhaust pipe, center exhaust pipe, rear exhaust pipe, and muffler w/tailspout.
-
This listing covers MY's 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, and 1974 Mercury Meteor (MY's 1962-63 only) & Comet's, including the Cyclone, Caliente and GT's, with their respective stock 144ci, 170ci, 200ci, and in 1969, the 250ci 6 cyl engine. Photo depicts the system for MY's 1963-65 Comet's with the stock 200ci. -
Listing covers model years 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1969, and 1970 Falcon's including SW & 1960-66 Ranchero's with the stock 6cyl. If you have a 1967-70 Ranchero; refer to SKU 518766 Photos depicts the system for MY's 1960-61 Ranchero's and station wagon's with the stock 6cyl.- Single exhaust consists of the front exhaust pipe, rear exhaust pipe, muffler, and tailpipe.
-
This listing covers model years 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, and 1969 Covair's stock with single exhaust. Photo depicts the system for MY's 1965-69 Corvair stock single exhaust, except Turbocharged.- This single exhaust system consists of the Y pipe, muffler and tail spout. Y pipe may be NORS. If we build the Y pipe, the flanges will not be OE correct. Our flanges will fit correctly but will not be formed (like the original flanges were). If you have the original flanges, you are welcome to send them to us and we will re-use them on the replacement exhaust pipes in whichever material desired.
-
This listing covers MY's 1960, 1961, 1962, 1963, 1964, 1965, and 1966 GMC ½T 1000, ¾T 1500, and 1T 2500's with the stock V6 305ci with 2WD. Excludes 4WD's. Photo depicts the stock single exhaust for 1963 GMC with the stock 305ci V6 & 2WD (except 7' panel truck & Suburban which require a different tailpipe).- Single exhaust system consists of cross-over pipe, Y pipe, rear exhaust pipe, muffler, and tailpipe.
-
This listing covers model years 1960, 1961, 1962, 1963, and 1964 Belvedere, Savoy, and Fury's with the stock V8 and dual exhaust. Excludes 1962's with a 413ci & 1963-64's with a 426 HP. Photo depicts the system for 1962 Belvedere, Savoy, and Fury's with the stock 383ci.- For MY's 1960-61 with a 383ci or 361ci this exhaust system consists of LS/RS front exhaust pipes, LS/RS rear exhaust pipes, LS/RS mufflers, and LS/RS tailpipes.
- For MY's 1960-61 with a 318ci, 1962-64 (all engines but 413ci or 426ci HP); this dual exhaust consists of LS/RS exhaust pipes, LS/RS mufflers, and LS/RS tailpipes.
-
This listing covers model years 1960, 1961, 1962, 1963, and 1964 Sunliner convertibles.- Single exhaust consists of the exhaust pipe, resonator, connector pipe, and muffler with tailpipes.
-
This listing covers 1960 and 1961 Fairlane's, for 1962 and up refer to Ford Mid Size listings. Also covers 1960, 1961, 1962, 1963, and 1964 Galaxie, Starliner, and Custom's with the stock V8 and a single exhaust. Photo shown is generic and is posted so that you might see the quality of our craftsmanship and the type of bending.- Single exhaust system consist of the Y pipe, rear exhaust pipe, and muffler with tailpipe. Y pipe may be NORS.
-
Our mufflers are a double walled shell. The end caps are roll-seamed. The outer wrap is smooth with no exposed welds. The baffles and end caps are a heavy gauge material.- This round muffler is stock with a body length of 27", stock inlet ID of 2", with tailspout and bracket welded in stock location.
-
This listing covers model years 1960, and 1961 Fairlane's (for 1962 and up refer to Ford Mid Size) 1960, 1961, 1962, 1963, and 1964 Galaxie, Starliner, 300's and Custom's with the stock V8 and dual exhaust, except Sunliner convertibles. For MY's 1960-61 Sunliner's, refer to listing 518711. For MY's 1962-64 Sunliner's, refer to listing 518716. Photo depicts the stock dual exhaust for 1963 Full Size with a 406ci or 427ci with long branch manifolds.- This dual exhaust system consists of the H pipe, LS/RS rear exhaust pipe, and LS/RS mufflers with tailpipe.
-
This listing covers model years 1960, 1961, 1962, 1963, and 1964 Dodge's with a V8 and stock with a single exhaust.
- Single exhaust system includes Y pipe, rear exhaust pipe, muffler, and tailpipe. Y pipe NORS only.
-
This listing covers model years 1960 & 1961 (without Ram Induction), 1962, 1963, and 1964 300's with dual exhaust and mufflers only (no resonators). If your 1960-61 Chrysler 300 was stock with Ram Induction refer to SKU 5987697. If your 1962-64 Chrysler 300 is stock with the Cross Ram engine, refer to listing 598702. Photo depicts the system for 1963-64 Chrysler 300's.- Dual exhaust system consists of LS/RS front exhaust pipes, LS/RS rear exhaust pipes, LS/RS mufflers, and LS/RS tailpipes.
- We received many inquiries regarding this system fitting 1963-64 New Yorker's. It will NOT due to the fact that the engine on the New Yorker's sits 1" higher to the manifold.
-
This listing covers model years 1960, 1961, 1962, 1963, and 1964 LeSabre, Invicta, Electra, and Wildcat's with a V8 and stock single exhaust. Photo depicts the system for 1962 Electra and Electra 225 stock with a single exhaust.- Single exhaust system includes Y pipe, center exhaust pipe, rear exhaust pipe, transverse muffler and tailpipe. Y pipe may be NORS. Metal-to-metal connection at the manifolds, no gaskets required.
-
This listing covers model 1960, 1961, and 1962 Dart, Phoenix, Pioneer, and Seneca stock with a dual exhaust. 1960 MY covers 361ci and 383ci engines, only. No dual's available for 1960 with a 318ci. Photo shown is generic and is posted so that you might see the quality of our craftsmanship and the type of bending.- Dual exhaust system consists of LS/RS exhaust pipes, LS/RS mufflers, and LS/RS tailpipes.
-
Photo depicted is for a 1960-61 Chrysler and is posted here since these systems are very similar in configuration (but require different parts).- Ram Induction dual exhaust system consists of LS/RS front exhaust pipes (AKA preheater tubes), LS/RS center exhaust pipes, cross-over (these 5 pipes make up an "H" pipe), LS/RS rear exhaust pipes, LS/RS mufflers, and LS/RS tailpipe along with the 1&1/8" clamps needed at the preheater tubes.
-
This listing covers MY's 1960 and 1961 Ford Sunliner convertibles.
- For 1960 models this dual exhaust consists of LS front exhaust pipe, LS resonator, LS rear exhaust pipe and LS muffler with tailspout while the RS will have a front exhaust pipe, rear exhaust pipe, and muffler with tailspout.
- For 1961 models this dual exhaust consists of LS front exhaust pipe, LS resonator, LS rear exhaust pipe, and LS muffler with tailspout while the RS consists of a long exhaust pipe and RS muffler with tailspout.
-
This listing covers model year 1960 & 1961 Dart, Lancer, and Swinger's stock with the Ram Induction set-up. Photo depicted is for a 1960-61 Chrysler and is posted here since these systems are very similar in configuration (but require different parts).
- Dual exhaust system consists of LS/RS front exhaust pipes, LS/RS Y (AKA center exhaust) pipes, crossover pipe, LS/RS rear exhaust pipes, LS/RS mufflers, and LS/RS tail pipes.
-
Listing covers model years 1960 and 1961 Dodge's with the Ram Induction set up. Photo depicted is for a 1960-61 Chrysler and is posted here since these systems are very similar in configuration (but require different parts).
- Ram Induction dual exhaust system consists of LS/RS front exhaust pipes (AKA preheater tubes), LS/RS center exhaust pipes, cross-over (these 5 pipes make up an "H" pipe), LS/RS rear exhaust pipes,LS/RS mufflers, and LS/RS tailpipes.
-
Listing covers MY 1960, and 1961 Desoto's stock with the stock V8 and single exhaust. Photo shown is generic and is posted so that you might see the quality of our craftsmanship and the type of bending.- Single exhaust system consists of a Y pipe (which comes in 3 sections), muffler, and tailpipe. Y pipe may be NORS.
-
This listing covers 1960 and 1961 DeSoto's with the Ram Induction set up. Photo depicted is for a 1960-61 Chrysler and is posted here since these systems are very similar in configuration (but require different parts).
- Ram Induction dual exhaust system consists of LS/RS front exhaust pipes (AKA preheater tubes), LS/RS center exhaust pipes, cross-over (these 5 pipes make up an "H" pipe), LS/RS rear exhaust pipes, LS/RS mufflers, and LS/RS tailpipes along with the 1&1/8" clamps needed at the preheater tubes.
-
Listing covers MY's 1960 and 1961 Chryslers stock with the Ram Induction setup. Photo is correct to the listing.
- Ram Induction dual exhaust system consists of LS/RS front exhaust pipes (AKA preheater tubes), LS/RS center exhaust pipes, cross-over (these 5 pipes make up an "H" pipe), LS/RS rear exhaust pipes, LS/RS mufflers, and LS/RS tailpipes along with the 1&1/8" clamps needed at the preheater tubes.
- The tailpipes are short on the 300; they end in front of the bumper and they are tucked up tightly under the trunk pan. You can’t see the tailpipe tips from the side of the vehicle.
- The tailpipe hangers attach at the radius of the turndown, not on a straight section of pipe. This is a Waldron's exclusive design.
-
This listing covers model years 1960 and 1961 Buick LeSabre, Invicta, Electra and Electra 225 with V8 dual exhaust and a transverse muffler. Photo depicts the stock dual exhaust for 1961 Buick Invicta's & LeSabre's with the stock V8.- The dual exhaust consists of the LS/RS front exhaust pipes (flange connected to the rear exhaust pipes), LS/RS rear exhaust pipes (flange connected to the transverse muffler inlets), dual in/dual out transverse muffler, and LS/RS tailpipes. Metal-to-metal connection at the manifolds, no gasket required.
-
This listing covers model years 1960 and 1961 Fairlane's (for 1962 & up refer to Ford Mid Size), 1960, 1962, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, and 1974 Galaxie, Starliner, and Custom's with a stock 6 cyl. Photo depicts the stock single exhaust for 1968 Full Size Ford's with the stock 240ci 6 cyl, except SW's.- Single exhaust consists of the exhaust pipe, muffler, and tailpipe.
-
This listing is currently for a 1960 Edsel convertible with a 352ci. We do not have the exhaust pipe patterns needed for the 292ci.
- Dual exhaust consists of LS has front exhaust pipe, resonator, connector pipe, and muffler with tailpipe while RS has front exhaust pipe, rear exhaust pipe and muffler with tailpipe. No resonator on the RS.
-
This listing covers 1960 Edsel's with the stock V8 332ci & 361ci. The 292ci V8 was stock with a single exhaust (only). Listing excludes Ranger convertibles. Photo shown is generic and is posted so that you might see the quality of our craftsmanship and the type of bending.
- Dual exhaust consists of H pipe, LS/RS mufflers, and LS/RS tailpipes.
-
This listing covers MY's 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, and 1974 for Rebel, Ambassador, Classic, Marlin, American, Gremlin, Hornet, Javelin and AMX's with V8 and single exhaust. Photo depicts the system for a 1965 AMC Rambler Ambassador with the stock 327ci.- For MY's 1959-62 this single exhaust system consists of 2 pc. Y (cross-over & Y pipe), muffler and tailpipe.
- For MY's 1963-64 3 Seat Station Wagons this single exhaust system consists of 2 pc. Y (cross-over & Y pipe), rear exhaust pipe, muffler and tailpipe.
- For MY's 1963-74 (except the 3 Seat SW) this single exhaust consists of the Y pipe, rear exhaust pipe, muffler, and tailpipe.
- Some Y pipes may be NORS.
-
This listing covers model years 1959, 1960, 1961, 1962 4bbl, 1964, 1965, and 1966 Thunderbird's. For MY 1962 with a 6bbl and 1963 T-birds, refer to 518724. Photo depicts the system for all 1961 Ford Thunderbirds.- For 1959-63 models this dual exhaust system consists of H pipe, LS/RS rear exhaust pipes with resonators, and LS/RS mufflers w/tailspouts.
- For 1964-66 models this dual exhaust system consists of H pipe, LS/RS rear exhaust pipes with resonators, and LS/RS mufflers built into the tailpipes.
-
This is a set of 4 OEM correct hangers for MY's 1959 and 1960. These hangers are used at the muffler outlets and on the frame rail prior to the rear axle. This set does not include the hangers needed at the rear. Hangers generally will ship within 1 wk. -
- This single exhaust consists of the front exhaust pipe, rear exhaust pipe, front muffler, connector pipe, rear muffler, and tailpipe.
-
This listing covers 1959 & 1960 Edsel Ranger, Corsair, & Villager Station Wagon's with the stock V8. Photo depicts the stock single exhaust for 1959 Edsel's with the stock V8 (this customer opted to cut the system).- For MY 1959 the single exhaust system consists of the Y pipe, muffler and tailpipe.
- For MY 1960 the single exhaust system consists of the Y pipe, rear exhaust pipe, and muffler with tailpipe.
-
This listing covers 1959 & 1960 Edsel's (exc. 1960 convertible) with the stock 6 cyl. Photo shown is generic and is posted so that you might see the quality of our craftsmanship and the type of bending.- For MY 1959 the single exhaust consists of the exhaust pipe, muffler, and tailpipe. Listing covers all body styles.
- For MY 1960 the single exhaust consists of the front exhaust pipe, rear exhaust pipe, and muffler with tailpipe. Listing excludes Edsel convertibles.
-
This listing covers model years 1959 and 1960 Bel Air, Biscayne, and Impala's with the stock V8 283ci, 348ci or 348HP and a dual exhaust with 2 mufflers and 2 resonators. Photo depicts the stock dual exhaust system for 1960 9Passenger SW's with the stock non-HO 348ci.- Dual exhaust system consists of LS/RS exhaust pipes, LS/RS mufflers, LS/RS front tailpipes with resonators, and LS/RS rear tailpipes.
- Systems for the 283ci or 348ci engines require a 3 bolt formed flange, starts out at 2" and reduces to 1 and 7/8" at the muffler outlet. Systems for the 348HP engine require a 3 bolt flat flange, starts out at 2½" and reduces down to 2" at the muffler outlet. The will be an additional cost of $40.00 charged at the check out process for the 348HP systems.
- Our pattern exhaust pipes have the piece that some call an extension (we call an insert) incorporated into the exhaust pipes. If you would prefer to have this insert/AKA extension a separate part, you may choose so in the check out process.
-
This listing covers model years 1959 and 1960 Chevy Full Size Bel Air, Biscayne and Impala with the stock dual exhaust but with the stock resonators eliminated. Photo shown is generic and is posted so that you might see the quality of our craftsmanship and the type of bending.- Dual exhaust system consists of LS/RS exhaust pipes, LS/RS mufflers, LS/RS front tailpipes with resonators eliminated, and LS/RS rear tailpipes.
- Systems for the 283ci or 348ci engines require a 3 bolt formed flange, starts out at 2" and reduces to 1 and 7/8" at the muffler outlet. Systems for the 348HP engine require a 3 bolt flat flange, starts out at 2½" and reduces down to 2" at the muffler outlet. The will be an additional cost of $40.00 charged at the check out process for the 348HP systems.
- Our pattern exhaust pipes have the piece that some call an extension (we call an insert) incorporated into the exhaust pipes. If you would prefer to have this insert/AKA extension a separate part, you may choose so in the check out process.
-
- This single exhaust system consists of the Y pipe, rear exhaust pipe, muffler, resonator w/long inlet pipe, and tailpipe.
-
This listing is for all body styles 1959 Pacer, Ranger, Citation, and Corsair's with the stock V8 and dual exhaust. Photo depicts the exhaust system for 1959 Edsel's, except convertibles and station wagons.- Dual exhaust system consists of LS/RS exhaust pipes, LS/RS mufflers, LS/RS front tailpipes and LS/RS rear tailpipes. From the factory, these tailpipes were all in 1 piece but are so long that they must be reproduced in 2 sections.
-
Photo depicts the system for MY 1959 Invicta and LeSabre.- Dual exhaust system consists of LS/RS exhaust pipes, LS/RS resonators, LS/RS connector pipes, LS/RS rear mufflers with tailspouts.
-
Photo shown is generic and is posted so that you might see the quality of our craftsmanship and the type of bending.- Single exhaust system consists of front exhaust pipe, rear exhaust pipe, front muffler, connector pipe, rear muffler, and tailpipe. Y pipe will be NORS only.