- This is a one piece unit and consists of the exhaust pipe, tapered muffler and tailpipe. Available in aluminized steel, only.
- Exhaust pipes does not take a flange, it has a flare that uses a special nut which is not provided.
- Refer to eBay for the copper gasket that is required.
-
This listing covers model years 1928, 1929, 1930, and 1931 Model A's. Photo depicted is correct to the listing. -
This listing covers model years 1952,1953, 1954, 1955, and 1956 Ford's stock with a 6 cyl. Photo depicts the stock single exhaust for 1955-56 Ford Station Wagon's and Sedan Deliveries with the stock 6cyl.- Single exhaust consists of the exhaust pipe, muffler, and tailpipe.
-
Photo shown is correct to the listing.- Dual exhaust system consists of LS/RS exhaust pipe, LS/RS mufflers, LS/RS front tailpipes and LS/RS rear tailpipes.
- This system starts out at 2"OD and reduces to 1¾"OD at the muffler outlet.
-
Listing covers model years 1965, 1966, and 1967 Mustang's with the stock V8 and single exhaust. Photo depicts the system for MY's 1965-66 Mustang's stock with a V8 and a single exhaust.- Single exhaust consists of the Y pipe, rear exhaust pipe with resonator, single in/single out (same end cap) transverse muffler, and tailpipe.
-
This listing covers model years 1962, 1963, 1964, 1965 and 1964 Fairlane's stock with a 6 cyl and single exhaust. Photo depicts the system for MY's 1963-65 Fairlane's with the stock 6 cyl.- 1962-65 models consist of the front exhaust pipe, rear exhaust pipe, and muffler w/tailpipe.
- 1966 models consist of the front exhaust pipe, rear exhaust pipe, and transverse muffler w/tailpipe.
-
This listing covers model years 1927, 1928, 1930, 1931, 1932, and 1933 Franklin's with the stock 6 cyl. engine. Photo depicts the stock single exhaust for 1927-28 Franklin Series 11B & 11C with the stock 6cyl.- This single exhaust consists of the exhaust pipe, muffler and tailpipe.
- For 1924-26 & 1929 Franklin's, refer to listing 453480.
- For 1933 Olympics', models 18 or 18B, refer to listing 453478.
-
This listing covers model years 1936, 1937, 1938, 1939, 1940, 1941, 1942, 1943, 1944, 1945, 1946, 1947, and 1948 Lincoln Continentals with the stock V12. Photo depicts the system for 1940-48 Continentals stock with the V12 and a Hot Air Heater- Single exhaust consists of the Y pipe, rear exhaust pipe, muffler, and tailpipe.
- You will be asked report with or without hot air heater in the check out process.
- 1940-48 MY's with the hot air heater will need to report the OD at the manifold.
-
This listing covers MY's 1953 and 1954 Lincolns with the stock V8. Photo depicts the system for 1954 Lincolns with the stock V8- This single exhaust system consists of the crossover pipe, exhaust pipe, front resonator, center muffler, connector pipe, rear resonator and tailpipe.
- Give Olson's Gaskets a call for the needed gaskets; 360-871-1207.
-
Photo depicted is correct to listing.- Dual exhaust system consists of the H pipe, LS/RS front mufflers, LS/RS connector pipe, LS/RS rear mufflers with tailpipes.
-
This listing covers model years 1932, 1933, 1934, 1935, 1936, 1937, 1938, 1939, 1940, 1941, and 1942 Oldsmobile's with the stock 8 cyl. Photo depicts a 1933 Oldsmobile F33.- Single exhaust system consists of the exhaust pipe, muffler and tailpipe.
-
This listing covers model years 1961, 1962, and 1963 F85 and Cutlass's with the stock 215ci and single exhaust. Photo depicts the stock single exhaust for 1963 F85 with the stock 215ci V8.- This system is a metal-to-metal connection at the manifold and no gaskets are required there. However, some of these Y pipes do require a gasket at the outlet end and unfortunately Waldron's does not have these gaskets available.
- Single exhaust system consists of the Y pipe (flange connection to), rear exhaust pipe, single in/single out same end transverse muffler, and tailpipe. Y pipe may be NORS.
- Original flanges were a formed flange which are NA. If the Y pipe for your system is not an NORS part, Waldron’s Exhaust will use universal flat flanges in reproducing the Y pipe. If you have the original flanges and would like us to reuse them on your system, you are welcome to ship them to us in advance of building your system.
- 1st Design: The propeller shaft center bearing support is mounted to the floor pan.
- 2nd Design: The propeller shaft center bearing support is mounted to the cross member. Rear exhaust pipe will have a flat area 34" from the outlet end.
- 3rd Design: The propeller shaft center bearing support is mounted to the cross member. Rear exhaust pipe is round through out (no flattened area).
-
This listing covers model years 1964, 1965, 1966, and 1967 Olds Cutlass & F85 stock with a V8 and single exhaust with muffler and resonator. Photo depicts the stock single exhaust for 1965-67 Olds F85's (except Vista Cruiser) with the stock 330ci V8 & 4bbl carburetor- Single exhaust system consists of the front exhaust pipe, rear exhaust pipe, front muffler, connector pipe, rear single in/single out transverse muffler, and tailpipe.
