-
This listing is for 1975 and 1976 Mercury Montego and Montego Villager SW's with the stock 460ci V8 and stock with dual's. Some models were stock with a single catalytic converter on the driver side while other had 2 converters. Photo shown is generic and is posted so that you might see the quality of our craftsmanship and the type of bending. Dual exhaust system starts behind the converter(s) and consists of the NORS H pipe, LS/RS mufflers, and LS/RS tailpipes. Report your converter set-up in the check out process. -
This listing covers MY's Ford LTD's (full size) stock with a dual exhaust and their respective 429ci or 460ci V8 & starts after the H pipe (which is not included). Photo depicts the H Pipe-Back dual exhaust for 1971 Ford Full Size models with the 429ci.- We can help you out with a set of mufflers, LS/RS front tailpipe, and LS/RS rear tailpipe.
- No aftermarket company ever reproduced the H pipes for these MY's and so we are unable to offer the complete system. If you have an original H pipe and would like to have us use it to reproduce your system, please contact us at 1-800-503-9428.
-
This listing covers MY 1970 (with a 429ci) 1970 & 1972 full size Mercury with the stock 429ci and 1974 full size Mercury's with the stock 460ci. Mercury did not offer dual exhaust systems on any full size cars in 1971 or 1973. No aftermarket company ever reproduced the H pipes for these MY's and so we are unable to offer the complete system. If you have an original H pipe and would like to have us use it to reproduce your system, please contact us.- We can help you out with the LS/RS mufflers, LS/RS front tailpipes, and LS/RS rear tailpipes.
-
This listing is for MY 1979 Mustangs with their respective stock 6 cyl or 8 cyl engines; 171ci, 200ci, or 302ci.
- This single cat-back exhaust starts behind the converter and consists of the rear exhaust pipe, front muffler, connector pipe, and rear muffler w/tailspout. If the front Y pipe and/or converter are need, please give us a call for pricing and availability.
-
This listing is for MY's 1964 & 1965 F85's that were stock with the Buick 225ci V6. Photo shown is generic and is posted so that you might see the quality of our craftsmanship and the type of bending.- Single exhaust consists of the Y pipe, rear exhaust pipe, muffler, and tailpipe. MY 1965 Y pipe may be NORS.
-
This listing covers MY's 1957, 1958, 1959, and 1960 Dodge D100, D200, D300 or W300 stock with the stock 318ci V8 and short tailpipe that dumps out before the rear axle. Photo is correct to the listing for all 1957-60 D100, D200, D300 & W300 with the stock 318ci and Y pipe with Option 2 flange rotation.- Single exhaust system consists of the Y pipe, rear exhaust pipe, muffler, and OE correct short tailpipe.
- You will be asked to report which of the 2 flange rotation options is needed for your Y pipe.
- Y pipe may be NORS
-
This listing covers MY's 1975, 1976, 1977, Dodge D100's, 1978, 1979, and 1980 D100's & D150, 1981 D150's and 1975, 1978, 1979, 1980, 1981 D200's stock with the 170ci 6 cyl and start behind the catalytic converter. If the pipes forward of the converter and/or the converter are needed, please contact us for availability and pricing.
- For MY 1975 this cat-back single exhaust system consists of the muffler and tailpipe.
- For MY's 1976-78 & 1980-81 (MY '78, '80 & '81 this is for systems without sound control) this cat-back single exhaust system consists of the muffler, front tailpipe and rear tailpipe.
- For MY 1979 D100 & D150's this cat-back single exhaust consists of the rear exhaust pipe, muffler, front tailpipe, center tailpipe, and rear tailpipe.
- For MY 1979 D200's this single cat-back exhaust consists of the center exhaust pipe, rear exhaust pipe, muffler, front tailpipe, center tailpipe & rear tailpipe.
-
This listing covers MY's 1975 D100 & D200's, 1976 & 1977 D100's, 1978 & 1979 D100, D150, & D200's, 1980 & 1981 D150 & D200's, 1982, 1983, 1984, 1985, & 1986 D150 & D250's, and 1987, 1988, and 1989 D150's with their respective stock V8 (318ci, 360ci, 400ci, and 440ci) and starts behind the catalytic converter. If the pipes forward of the converter and/or the converter are needed, please contact us for availability and pricing.
- For MY 1975 D100 & D200's w/318ci or 360ci this cat-back single exhaust consists of the muffler and tailpipe.
- For MY's 1976-77 D100's w/318ci or 360ci this cat-back single exhaust consists of the muffler, front tailpipe, center tailpipe, and rear tailpipe.
- For MY 1978 D100, D150 & D200's w/318ci, 360ci, 400ci, or 440ci this cat-back single exhaust consists of the rear exhaust pipe, muffler, front tailpipe, center tailpipe, & rear tailpipe.
- For MY 1979 D100, D150 & D200's w/318ci or 360ci this cat-back single exhaust consists of center exhaust pipe, rear exhaust pipe, muffler, front tailpipe, center tailpipe & rear tailpipe.
- For MY's 1980-81 D150 & D200's w/318ci or 360ci this single cat-back exhaust consists the muffler, front tailpipe, center tailpipe, & rear tailpipe.
- For MY's 1982-87 D150 w/318ci or 360ci & MY 1988 w/360ci this single cat-back exhaust consists of the muffler, front tailpipe, center tailpipe & rear tailpipe.
- For MY's 1982-86 D250's w/318ci or 360ci & 1988-89 D150 w/318ci this single cat-back exhaust consist of the rear exhaust pipe, muffler, front tailpipe, center tailpipe, & rear tailpipe.
-
This listing covers MY's 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987, 1988 & 1989 Dodge D100's, D150's and D250's with the stock 6 cyl and starts behind the catalytic converter. If the pipes forward of the converter and/or the converter are needed, please contact us for availability and pricing. Photo depicts the stock cat-back single exhaust for 1980-87 Dodge D100's, D150's, D200's & D250's with the stock slant 6 225ci and 131" WB (also shown in photo is the rear section of the stock catalytic converter built for this customer).- For MY's 1980-87 D100's w/225ci this single exhaust consists of muffler, front tailpipe and rear tailpipe.
- For MY's 1982-83 D150's & 1982-86 D250's w/225ci this single cat-back exhaust consists of the muffler, front tailpipe and rear tailpipe.
- For MY's 1984-87 D150's & 1987 D250's w/225ci this single cat-back exhaust consists of the rear exhaust pipe, muffler, front tailpipe and rear tailpipe.
- For MY's 1988-89 D150's & D250's w/3.9L this single cat-back exhaust consists of the muffler, front tailpipe, center tailpipe, and rear tailpipe.
-
This listing covers MY's 1967, 1968, 1969, 1970, 1971, 1972, 1973, and 1974 Ford Broncos with their stock V8 289ci or 302ci. Photo depicts the stock single exhaust for 1970-74 Ford Bronco's with the stock V8 302ci.- Single exhaust system consists of the cross-over pipe, Y pipe (AKA 2 pc. Y pipe), muffler, and tailpipe.
-
This listing covers MY's 1954, 1955, and 1956 Dodge ½T's with the stock V8. Photo is correct to the listing.- Single exhaust system consists of cross-over pipe, Y pipe (AKA 2 pc. Y pipe), rear exhaust pipe, muffler, and tailpipe.
-
Waldron's Exhaust has custom designed exhaust pipes that allows owners of a 1964 or 1965 Lemans, Tempest, or GTO's to use the Ram Air or High Output manifolds which were not stock in these model years.
- Dual exhaust consists of the LS/RS exhaust pipes, LS/RS mufflers, and LS/RS tailpipes.
- This system starts out at 2¼"OD on the exhaust pipes which reduce to 2"OD at the muffler inlets and then increases to 2¼" OD at the tailpipes.
- If the cast iron flanges are needed, add them to your cart for an additional $45.00.
-
This listing covers MY's 1966, 1967, and 1969 Pontiac GTO, Tempest, and Lemans' stock with a dual exhaust system with mufflers and resonators. 1968 all mid-size's & 1969 GTO's with a 400ci & standard transmission were all stock with mufflers only, for the correct system refer to listing 453475 if you have a HO or Ram Air set-up or 453210 for non-HO or Ram Air. Photos depicts the system for a 1969 GTO stock w/automatic transmission.- Dual exhaust consists of the LS/RS exhaust pipes, LS/RS mufflers, LS/RS connector pipes, and LS/RS resonators with turndowns.
- In the check out process you will be asked to report w/ or w/o Ram Air or HO. There is an additional cost of $50.00 in aluminized steel or $100.00 in T409 for RA or HO. You will also be asked whether you have the cast iron flanges or if you need them added to your cart. If you already have the needed cast iron, you will need to send them to Waldron's in advance.
- 1966 & 1967 resonators are bullet style while 1969 resonators are cannister style.
-
Our mufflers are a double walled shell. The end caps are roll-seamed. The outer wrap is smooth with no exposed welds. The baffles and end caps are a heavy gauge material.- Waldron's has brought this muffler back to provide a close match to the original sound, enhanced flow rate from the original, while maintaining the OE look and size. The interior design is derived from the OE Pontiac part. Muffler cavities are packed with sound absorbing materials to compensate for the increased sound levels created by the larger interior diameters. The muffler dimensions are; 4.75 inches X 9.75 inches oval cross-section. The case is 22.75 inches in length with an over-all of 27.75 inches.
-
Our mufflers are a double walled shell. The end caps are roll-seamed. The outer wrap is smooth with no exposed welds. The baffles and end caps are a heavy gauge material.- This round muffler is stock with a body length of 27", stock inlet ID of 2", with tailspout and bracket welded in stock location.
-
Our mufflers are a double walled shell. The end caps are roll-seamed. The outer wrap is smooth with no exposed welds. The baffles and end caps are a heavy gauge material.- Inlet & outlet nipples cannot be any longer than 7"
- Regarding 4" round mufflers with an offset in/offset out position; the nipples cannot be any larger than 1½"ID
- Regarding 4" round mufflers with a center in/center out position: the nipples cannot be any larger than 2¼"ID
-
Our mufflers are a double walled shell. The end caps are roll-seamed. The outer wrap is smooth with no exposed welds. The baffles and end caps are a heavy gauge material.- Use this listing to build your own custom oval muffler. You tell us what you need and we will get it built for you. There will be no returns on custom built mufflers so be sure you triple check your measurements.
-
Our mufflers are a double walled shell. The end caps are roll-seamed. The outer wrap is smooth with no exposed welds. The baffles and end caps are a heavy gauge material.
- Select this option if you are looking for a stock replacement oval muffler. The checkout process will ask questions regarding your application and muffler will be built to the stock specifications.
- Excludes 1961-69 Lincoln Continentals.
-
Our mufflers are a double walled shell. The end caps are roll-seamed. The outer wrap is smooth with no exposed welds. The baffles and end caps are a heavy gauge material.- Select this option for a stock round muffler with a body length between 30"-38". The check out process will ask questions to determine what your vehicle is and the muffler will be built to the stock specifications.
-
Our mufflers are a double walled shell. The end caps are roll-seamed. The outer wrap is smooth with no exposed welds. The baffles and end caps are a heavy gauge material.- Select this listing if your stock round muffler is 39" or longer in the body length (AKA case). The checkout process will determine the muffler specifications needed for your application.
-
Out of stock
This muffler hanger is used on most 1941-66 Chevy trucks and on 1959-66 GMC trucks & vans. The strap is made of stainless steel. Currently unavailable. -
This is a set of 4 OEM correct hangers for MY's 1959 and 1960. These hangers are used at the muffler outlets and on the frame rail prior to the rear axle. This set does not include the hangers needed at the rear. Hangers generally will ship within 1 wk. -
Waldron's Exhaust reproduces these OEM style muffler hangers for MY's 1961, 1962, and 1963 Lincoln Continentals. Available for $127.00 for both LS/RS muffler (which are in the rear) hanger. Hangers generally will ship within 1 wk. -
Waldron's Exhaust reproduces these OEM correct hangers. Hangers generally will ship within 1 wk. -
Set of 4 OEM style hangers - 2 at the muffler and 2 at the tailpipes. Kit includes OEM correct rear tail pipe clamps. This set of OEM style hangers will fit all 1964-72 GM A-Body styles. Excluding Vista Cruisers and/or Station Wagons. Muffler hangers : ALL 68-72 A body / $49 per pair Tailpipe hangers: 64-67 Cutlass & 442 (without chambered tailpipe): $34 per pair 68-9 Olds 442 (for chrome tips): $57 per pair 68-69 Cutlass (without chrome tips): $45 per pair 70-72 Olds 442: $57 per pair 70-72 dual without bumper cutouts or trumpets: $45 per pair 70-72 Chevelle dual (without resonators or chrome tips): $45 per pair 68-71 Pontiac LeMans/Tempest/GTO: $57 per pair To order individual components, please call us at 800-503-9428. Hangers generally will ship within 1 wk. -
- Dual Exhaust: 1965-66 Ford full size V8 and 1965 Mercury Station Wagon V8
- Single Exhaust: 1966 Ford full size all models w/352 & 1966 SW w/289, 1966 Mercury SW
-
The Mustang Arvinode hanger kit includes the 4 OEM style hangers, 4 Ford clamps, and 2 clamps used at the resonator. Hangers generally will ship within 1 wk. -
Waldron's Exhaust reproduces these OE correct muffler hangers. The price of $56.00 is per hanger. This hanger is used on both single and dual exhaust systems. Select the number of hangers needed in the check out process. Hangers generally will ship within 1 wk. -
These OEM correct resonator hangers will fit MY's 1966, 1967, 1968, and 1969 Lincoln Continentals. Hangers generally will ship within 1 wk. -
Waldron's Exhaust reproduces this OE correct muffler hanger which was stock on multiple systems. Order the amount needed. This hanger fits:- 1967-68 Ford 6 cyl, 8 cyl single exhaust & LS/RS dual exhaust at the muffler outlet.
- 1967-71 Ford Thunderbird LS/RS dual at the muffler outlet.
- 1969-71 Lincoln Mark III LS/RS dual at the muffler outlet.
- 1967-68 Mercury 8 cyl single & LS/RS dual at the muffler outlet.
-
Waldron's Exhaust reproduces these OE correct muffler hangers. These muffler hangers fit 1968-69 Ford Mustangs and Mercury Comets. Used in both single and dual exhaust systems. Order for single or dual exhaust below. Hangers generally will ship within 1 wk. -
Waldron's Exhaust reproduces these OEM correct rear tailpipe hanger for 1968,1969, and 1970 Javelin's stock with a 6cyl, 1968, 1969, and 1970 AMX's and Javelin's stock with a V8 single and/or dual exhaust. Hangers generally will ship within 1 wk. -
Waldron's Exhaust reproduces this set of 4 OE correct hangers for 1968,1969and 1970 AMC Javelin's and AMX's. This set consists of the LS/RS front and rear tail pipe hangers. This part will generally ship within 1 wk. -
Waldron's Exhaust reproduces these OE correct front and rear tailpipe hangers for 1968 1969, 1970 AMX and Javelin's. This part will generally ship within 1 wk. -
Waldron's Exhaust reproduces this OE correct muffler hanger. This muffler hanger was used on 1970 and 1971 Ford Torino's / Fairlane's and Mercury Montego's. All engines. Both single and dual exhaust systems. Simply order the amount needed. Hangers generally will ship within 1 wk. -
Waldron's Exhaust reproduces this OE correct muffler hanger. This muffler hanger is correct to:- 1967 Ford Fairlane's (except 289ci & Junior Jewel)
- 1968 Ford Falcon (except for S.W.)
- 1967 Mercury Comet's (except Junior Jewel)
Questions? Call Us Today! (269) 467-7185 or (800) 503-9428
