- Dual conversion kit consists of the exhaust pipes, custom-built glasspacks, tailpipes, blocker plate, gaskets and clamps. Gaskets & steel clamps are included. After 1949, the RS exhaust requires blocking plate which will be included in the system. Universal hangers can be added to the cart, if needed. Period specific hangers are N/A.
- The system goes through existing holes in the crossmembers. LH exhaust pipe starts at 1 ½”OD and opens to 2”OD at the glasspack inlet. RH exhaust pipe 2” OD throughout. Tailpipes are either 1 5/8” or 1 ¾” depending on the material selected & MY.
- If you would prefer mufflers (over glasspacks), you may make that change to your order in the check out process. Additional cost of $115.00 for aluminized steel or $230.00 for T409 SS.
-
Listing covers MY's 1935, 1936, 1937, 1938, 1939, 1940, and 1941 Ford ½T Trucks with the stock flathead V8. Convert your flathead Ford to dual exhaust with Waldron's exclusive Dual Conversion kits! Complete kit bolts on to the stock manifolds. Not available for 1933-34, 1942-47 or 1953 MY's. -
This listing covers model years 1954, 1955, 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, and 1964 Ford F100, F250, and F350's with the stock V8 and single exhaust. Photo depicts the stock single exhaust for 1954-56 F100, F250, & F350's with the stock V8.- Single exhaust system consists of the 2 pc. crossover pipe, exhaust pipe, muffler, and tailpipe.
-
This listing covers model years 1929, 1930, 1931, 1932, 1933, 1934, 1935, 1936, 1937, 1938, 1939, and 1940 Chevy trucks with a 6 cyl engine. For MY's 1929-32, this system is an alternative to the original 1 pc. design. Photo depicts the stock single exhaust for 1929-31 Chevy ½T with the stock 6cyl.- Single exhaust system consists of the exhaust pipe, muffler, and tailpipe.
-
Convert your 1957, 1958, or 1959 Chevy ½T, ¾T, or 1T with a small block 283ci V8 to dual's with Waldron's exclusive dual conversion kits that bolt onto your original manifolds that dump straight down with 3blt connection. Photo depicts the system for MY's 1957-59 Chevy ½T's with a long wheel base and the stock 283ci.- Dual conversion kit consists of gaskets, clamps, LS/RS front exhaust pipes, LS/RS rear exhaust pipes, LS/RS custom-built glasspacks, and LS/RS tailpipes. The 4 universal hangers are not included but can be added to your cart.
- System is 2" throughout.
-
This listing covers MY's 1967, 1968, 1969, 1970, 1971, and 1972 Chevy C10, C20, and C30's with the stock small block V8 327ci, 307ci or 350ci engine and lets you convert your small block Chevy, with the stock 45° angle manifolds, to dual exhaust. Photo depicts the dual conversion system for 1971-72 Chevy C20's ¾T 2WD with the stock 350ci V8 and 127"WB with rear leaf springs.- Dual exhaust conversion kit consists of the LS/RS front exhaust pipes, LS/RS rear exhaust pipes, LS/RS glasspacks, and LS/RS tailpipes, along with the gaskets and clamps needed. Universal hangers are additional and can be added to your cart.
- Exhaust system is 2" throughout.
-
This listing covers model years 1973, 1974, 1975, 1976, 1977, and 1978 Chevy C10, K10, C20, K20, C30's, Suburban's & Blazer's with the stock V8. Excludes K30's due to lack of patterns. Photo depicts the stock single exhaust for 1974 K5 Blazer's with 4WD & the stock 350ci.- Single exhaust consists of the Y pipe, rear exhaust pipe, muffler, and tailpipe. Y pipe may be NORS.
-
This listing covers MY's 1975, 1976, 1977, and 1978 Chevy C10, K10, C20, K20, C30, K30 & Suburban's with the stock 350ci, 400ci, & 454ci. For 1975-78 Suburban's with the 454ci this is a resonator eliminator option since all were stock with resonators. Photo depicts the stock dual exhaust for 1975 Chevy C10's with the stock 454ci.- Dual exhaust system for the 2 WD C Series consists of LS/RS exhaust pipes, LS/RS mufflers, & LS/RS tailpipes.
- Dual exhaust system for the 4 WD K Series & Suburban's consists of LS/RS front exhaust pipes, LS/RS rear exhaust pipes, LS/RS mufflers & LS/RS tailpipes.
-
This listing covers model years 1939, 1940, 1941, 1942, 1943, 1944, 1945, 1946, 1947, 1948, 1949, 1950, 1951, 1952, and 1953 GMC's with the stock 6 cyl 228ci or 248ci.- Single exhaust system consists of the exhaust pipe, muffler, and tailpipe.
- This exhaust pipe will not come with the cast iron flange. You will need to reuse your flange. Nor do we have a gasket available.
- The OE muffler hanger, available in checkout, is for MY's 1941-53. It is not OE correct for MY's 1939-40. Currently NA
-
This listing covers model years 1950, 1951, 1952, 1953, 1954, 1955, 1956, 1957, 1958, and 1959 GMC 1½T's with the stock 6 cyl. Photo depicts the single exhaust system for 1955-58 GMC truck models 100-24, 150-24, 250-24 & PM250-24 with the stock 6 cyl- Single exhaust consists of the exhaust pipe, muffler, and tailpipe. Flange is not included with this exhaust pipe. Reuse original cast iron flange (if possible).
-
Photo is correct to the listing.- 1962 & 1963 Olds Jetfire Turbo 2nd Design single exhaust system consists of the front exhaust pipe (AKA cross-over pipe), center exhaust pipe (AKA turbo outlet pipe), rear exhaust pipe, connector pipe (AKA over-axle pipe), single in/dual out transverse muffler, and LS/RS tailpipes.
- Waldron's Exhaust also has the turbo inlet pipe available for $60.00 or in T409 SS for $99.00. Simply add it to your cart, if needed.
-
This listing covers MY's 1961, 1962, 1963, and 1964 Mercury Monterey's, Commuter's, Colony Park's, and Montclair's with the stock V8 292ci, 352ci, 390ci, 406ci, & 427ci. For convertibles go to see listing 453451. Photo depicts the stock dual exhaust system for 1963 Mercury Monterey's & Colony Park's with the stock 390ci V8, except for convertibles.- System consists of the H pipe, LS/RS rear exhaust pipes, and LS/RS mufflers w/hanger bracket and tailspout welded into the proper position.
-
This listing covers MY's 1962, 1963 Mercury Meteor's & 1963, 1964, & 1965 Comet (including Cyclone and Caliente's) with their respective stock V8; 221ci, 260ci, or 289ci. 1965 . Photo depicts the system for 1965 Comet's.- Single exhaust consists of the Y pipe, rear exhaust pipe, muffler, and tailspout. Y pipe may be NORS.
- Comet's with the 4bbl carburetor were stock from the factory with a resonator built into the tailpipe. Waldron's does not have the needed pattern for the 4bbl set-up, so this listing is a resonator delete system.
-
This listing is for 1988 Mercury Cougars stock with the 302ci. Photo depicted is correct to the listing.- This single-into-dual exhaust system starts behind the converter. This consists of the NORS Y pipe (sits like a wishbone), LS/RS mufflers, and LS/RS tailpipes.
-
This listing covers MY's 1966, 1967, 1968, & 1969 Pontiac Custom, GTO, Lemans, & Tempest with Ram Air or High Output, 1970 models with Ram Air, and 1971-72 models with High Output. If your MY 1966, 1967, or 1969 was stock with 4 mufflers, refer to listing 453477. For systems w/o RA or HO, refer to listing 453210. Photo depicts the stock dual exhaust system for 1967 Pontiac Lemans, Tempest, and Custom with RA or HO manifolds on the stock 400ci V8 & standard transmission (this is a resonator eliminator system for 1967 GTO's with RA or HO & STD trans).- This dual exhaust system consists of the LS/RS exhaust pipes, LS/RS mufflers, and LS/RS tailpipes.
- This system starts out at 2¼"OD on the exhaust pipes which reduce to 2"OD at the muffler inlets and then increases to 2¼" OD at the tailpipes.
- For MY's 1970-72, this system does not include the chrome tips but will be designed to fit up to the stock tip design.
- If the cast iron flanges are needed, add them to your cart for an additional $45.00.
- Metal-to-metal connection at the manifolds. Gaskets are not required.
-
Our mufflers are a double walled shell. The end caps are roll-seamed. The outer wrap is smooth with no exposed welds. The baffles and end caps are a heavy gauge material.- This round muffler is stock with a body length of 27", stock inlet ID of 2", with tailspout and bracket welded in stock location.
-
Out of stock
This muffler hanger is used on most 1941-66 Chevy trucks and on 1959-66 GMC trucks & vans. The strap is made of stainless steel. Currently unavailable. -
Waldron's Exhaust reproduces this OE correct muffler hanger used at the outlet end of the resonator. Used in 1972 & 1973 by Ford on the Thunderbird and by Lincoln on the Mark IV. This hanger is 5¾"Lx2"W and are $12.00 per hanger. Order the amount needed. Hangers generally ship out within 1 wk. -
Listing covers MY's 1970. 1971, 1972, 1973, & 1974 Maverick's with the stock 6 cyl. and 1 muffler. If your 1973-74 Maverick was stock with 2 mufflers, refer to 518892. Photo depicts the stock single exhaust for 1971-72 Ford Maverick 2dr. models with the stock 170ci or 200ci 6cyl.- System consists of the front exhaust pipe, center exhaust pipe, rear exhaust pipe, and muffler w/tail spout.
-
Covers MY's 1971, 1972, 1973, & 1974 Maverick's with the stock V8 single exhaust with muffler & resonator. Photo depicts the stock V8 single exhaust with resonator for 1971-73 Mavericks with 2 doors (4dr models require a different rear exhaust pipe).- System consists of the front exhaust pipe (AKA Y pipe), center exhaust pipe w/resonator, rear exhaust pipe, & muffler w/tail spout. Y pipe may be NORS.
-
This listing covers MY's 1932, 1933, 1934 & 1935 Lincoln K Series stock with the V12. Photo depicts the stock single exhaust for 1932-33 Lincoln K Series with the stock V12- Single exhaust consists of the exhaust pipe, muffler, and tailpipe. Original exhaust pipe was 2¾"OD. In reproduction it will be 2"OD flared to 2¾"OD with a flat flare. We do not have the needed gasket available or the proper flange for this connection. If you have the original cast iron flange, you will want to reuse it.
-
Photo is correct to this stock dual exhaust listing.- Stock Dual exhaust system includes LS/RS exhaust pipes, LS/RS resonators, LS/RS connector pipes, dual in/dual out transverse muffler and LS/RS tailpipes.
- Stock pipe diameter is 2¼"OD through out.
-
This listing covers model years 1957, 1958, 1959, 1960 Rambler American, 1961, 1962, 1963, 1964 Rambler, American & Classic, 1965 & 1966 American, Classic along with Nash Marlin & Ambassador stock with the OHV 6 cyl. Photo depicts the stock single exhaust for 1964 AMC American's stock with the OHV 6cyl 196ci (except convertibles & station wagons).- For MY's 1957-63 (exc. 1962-63 convertibles) this single exhaust system consists of the exhaust pipe, muffler, and tailpipe. 1962-63 convertibles take a front exhaust pipe, rear exhaust pipe, muffler, and tail pipe.
- For MY's 1964-66 these single exhaust systems vary between models and body styles, with some set-ups having a transverse muffler.
- MY's 1957-60 all body styles except station wagon's need to report whether the car was stock with or without a wheel carrier.
-
This listing covers MY's 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, and 1974 for Rebel, Ambassador, Classic, Marlin, American, Gremlin, Hornet, Javelin and AMX's with V8 and single exhaust. Photo depicts the system for a 1965 AMC Rambler Ambassador with the stock 327ci.- For MY's 1959-62 this single exhaust system consists of 2 pc. Y (cross-over & Y pipe), muffler and tailpipe.
- For MY's 1963-64 3 Seat Station Wagons this single exhaust system consists of 2 pc. Y (cross-over & Y pipe), rear exhaust pipe, muffler and tailpipe.
- For MY's 1963-74 (except the 3 Seat SW) this single exhaust consists of the Y pipe, rear exhaust pipe, muffler, and tailpipe.
- Some Y pipes may be NORS.
-
This listing covers model years 1967, 1968, and 1969 AMC American/Rambler's with a straight 6 cyl. Photo depicts the stock single exhaust for 1967-68 AMC Rambler American's HT's & Sedan's with the 199ci 6cyl. Convertibles & SW require a different system, as does the 232ci 6cyl.- The single exhaust system consists of front exhaust pipe, rear exhaust pipe, muffler, and tailpipe.