- Single exhaust system consists of the crossover pipe, Y pipe, muffler, and tailpipe.
-
This listing covers model years 1942, 1943, 1944, 1945, 1946, 1947, 1948, 1949, 1950, 1951, 1952, and 1953 Ford F1, F2, F3, F4, F5 and F6's stock with the V8 and single exhaust. Photo depicts the crossover pipe and Y pipe for 1942-52 F1, F2, & F3's with V8, the muffler and tailpipes vary. -
This listing covers model years 1966, 1967, 1968, 1969, 1970, and 1971 Fairlane & Torino's, 1970-71 Ranchero's with the stock V8 and stock dual exhaust. Excludes 1966-69 Ranchero's & SW's which were stock with a single exhaust only. For 1967 Fairlane & Torino models, this is a resonator eliminator option. For the stock set up, refer 518765. Photo depicts the system for a 1970 Torino SCJ- Dual exhaust consists of the H pipe, LS/RS rear exhaust pipes, LS/RS mufflers, and LS/RS tailpipes.
-
This listing covers model years 1957, 1958 and 1959 Ford retractable hardtop's and convertibles with the stock V8 and dual exhaust. For 1958 Convertibles, this is a resonator eliminator options. If you would like to keep your convertible stock with the resonators, please give us a call. Photo depicts the system for 1957 Skyliner Retractable Hard Tops with the stock V8.- Dual exhaust system consists of LS/RS front exhaust pipes, mufflers, LS/RS front tailpipe, and LS/RS rear tailpipes.
- The front and rear tailpipe sections are different between a Retractable Hard Top and a soft-top Convertible. Please report the body-style appropriately.
-
Listing covers MY's 1960 and 1961 Chryslers stock with the Ram Induction setup. Photo is correct to the listing.- Ram Induction dual exhaust system consists of LS/RS front exhaust pipes (AKA preheater tubes), LS/RS center exhaust pipes, cross-over (these 5 pipes make up an "H" pipe), LS/RS rear exhaust pipes, LS/RS mufflers, and LS/RS tailpipes along with the 1&1/8" clamps needed at the preheater tubes.
- The tailpipes are short on the 300; they end in front of the bumper and they are tucked up tightly under the trunk pan. You can’t see the tailpipe tips from the side of the vehicle.
- The tailpipe hangers attach at the radius of the turndown, not on a straight section of pipe. This is a Waldron's exclusive design.
-
This listing covers model years 1961, 1962, 1963, and 1964 Star Chief, Bonneville, Catalina, and Grand Prix's (1962-64) with the stock V8 and a dual exhaust. For MY 1964 stock with the 421HO, this is a resonator eliminator option. Photo depicts the system for full size Pontiac's with the stock 389ci.- Dual exhaust consists of LS/RS exhaust pipes, LS/RS mufflers, and LS/RS tailpipes.
- MY's 1963-64 do not require gaskets at the manifolds. The connection is metal-to-metal.
-
Listing covers model years 1918, 1919, 1920, 1921, 1922, 1923, 1924, 1925, 1926, 1927, 1928 w/6 cyl., 1929, 1930, 1931, 1932, 1933, 1934, 1935 and 1936 Packard's. Waldron's does not have the patterns for a 1928 Packard with an 8 cyl. Photo depicts system for a 1935 Packard.- Single exhaust system consists of the exhaust pipe, muffler, and tailpipe.
-
This listing covers model years 1965, 1966, 1967, 1968, and 1969 Mustangs with a V8 and allows owners of A Code's & some K Code's to update their Mustang's to the unique sound of the Arvinode dual exhaust. For 1965-66 K Code's this is close in appearance and sound to the stock set up. If you would like to have the stock set up for your 1965-66 K Code, which has the factory correct chamber tube tied into the muffler/resonators, please refer to listing 518737. The Base Model does not have the chamber tube that runs along the top of the muffler/resonators which gives the Concours the OEM correct look for 1965-66 K Code models. Photo depicted is correct to the listing.- The Base model Arvinode dual system starts behind the stock H pipe and includes LS/RS connector (AKA rear exhaust pipes), LS/RS wave-tuned front mufflers WITHOUT externally mounted rectangular tubes, LS/RS over-axle pipes, LS/RS resonators with turndowns or GT exit.
- These parts were welded into LS and RS assembly's from the factory and connected with clamps to the outlet end of the H pipe.
- If the H pipe is needed, add it to your cart in the check out process.
- Let us know if you need the GT exit or turndowns in the check out process.
-
This listing covers model years 1965, 1966, 1967, 1968, 1969, and 1970 Ford Custom, LTD, and Galaxies with the stock V8 and dual exhaust. Includes convertibles and station wagon's. Excludes 1966 and 1967 7 Liter systems. Photo depicts the system for a 1966 Galaxie with the stock 352ci.- For all model years but 1965 SW this dual exhaust consists of the H pipe, LS/RS mufflers, LS/RS front tailpipes, and LS/RS rear tailpipes. Tailpipe were 1 piece from the factory but come in 2 pieces in reproduction. H pipe may be NORS.
- 1965 full size station wagon has the H pipe, LS/RS mufflers, LS front, center and rear tailpipes and RS front and rear tailpipes. H pipe may be NORS.
-
This listing covers model years 1975, 1976, 1977, 1978, 1979, 1980, 1981, 1982, 1983, 1984, and 1985 Eldorado's. Photo depicts the cat-back system for 1975-78 Fleetwood Eldorado's.- Cat-back system consists of rear exhaust pipe, front muffler, connector pipe, rear muffler and short tailpipe. If converter and/or pipes off the manifold are needed, please give us a call for pricing and availability.
-
This listing covers model years 1936, 1937, 1938, 1939, 1940, 1941, 1942, 1943, 1944, 1945, 1946, 1947, and 1948 Buick's with a straight 8. This listing is for MY's 1941-46 Buick's stock with a single carburetor set up. If your 1941-46 Buick was stock with a dual carburetor set-up refer to listing 568792. Photo depicts the system for a 1938 Buick 40 Series Special.- For MY's 1936-39 this single exhaust system consists of exhaust pipe, muffler, and tailpipe.
- For MY's 1940-48 this single exhaust system consists of the front exhaust pipe, rear exhaust pipe, muffler, and tailpipe.
-
Waldron's Exhaust reproduces this set of 4 OE correct hangers for 1968,1969and 1970 AMC Javelin's and AMX's. This set consists of the LS/RS front and rear tail pipe hangers. This part will generally ship within 1 wk. -
This listing covers model years 1950, 1951, 1952, 1953, 1954, 1956, 1957, 1958, 1957, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, and 1971 International ½T, ¾T, and 1T's L110, L111, L112, L120, L121, L122, L130, R100, R102, R110, R111, R120, R121, R122, S100, S110, S112, S130, A110, A120, A130, B100, B110, B120, B130, C110, C120, C130, 1100A, 1200A, 1300A, C1000, D1000, C1100, D1100, C1200, D1200, C1300, D1300's stock with 2WD (excludes 4WD) and 1972, 1973, 1974, and 1975 International ½T, ¾T, and 1T's 1010, 1110, 1210, 1310, MS1210, 100 & 200 with either 2WD or 4WD . Photo depicts the exhaust system for 1956 International ½T-2T with the stock BD220ci 6 cyl engine and with the spare tire carrier mounted on the left side, front of the bed on the outside. Through the check out process be sure to let us know where the spare tire is located on your International and for MY's 1974 International 100 or 200 & 1975 International 100, 150, and 200's with the 258ci, be sure to give us your axle code.- Single exhaust system consists of the exhaust pipe, muffler, and tailpipe.
- For MY's 1950-61: Exhaust pipe will not come with a flange (replacement is NA). You will need to keep the original cast-iron flange and reuse it.
- For MY's 1962-75: Exhaust pipe will come with a flange however if you have an original cast iron flange, keep and reuse it
-
This listing covers model years 1948, 1949, 1950, 1951, and 1952 Ford ½T, ¾T & 1T trucks with the stock flathead V8. Convert your flathead Ford to dual's with Waldron's exclusive Dual Conversion kits! Complete kits bolt on to the original manifolds. Photo depicts the dual conversion for 1948-52 Ford F1 with the stock V8- Dual conversion kit consists of the LS/RS front exhaust pipes, LS/RS rear exhaust pipes, LS/RS glasspacks, LS/RS tailpipes, gaskets, and clamps.
- Period specific hangers are N/A. Universal hangers only. Hangers are not included in the kit but may be added to your cart.
- Exhaust pipes start out at 1&5/8" OD and increase to 2"OD immediately after the flange. Tail pipes are 1¾"OD.
- If you would prefer mufflers (over glasspacks), you may make that change to your order in the check out process.
-
This listing covers 1972, 1973, & 1974 Commando's, Wagoneer's, J10's, J20's, CJ5 and CJ6's with the stock V8. Photo depicts a 1972-73 Jeep Commando with standard transmission.- Single exhaust system consists of a crossover pipe, Y pipe, muffler, and tailpipe.
- System is a metal-to-metal connection at the manifold. No gaskets are required at 2 pc. Y pipe.
- If you have a 1972-73 CJ5 or CJ6 you will need to report the desired tailpipe diameter. These models were stock with either 1¾" or 2" OD tailpipe.
-
This listing covers model years 1952, 1953, 1954, 1955, and 1956 Cadillac's (all series and all body styles) with stock dual exhaust with 4 mufflers. Photo depicts the system for 1952-53 Cadillac coupes and convertibles.- Dual exhaust system includes - LS/RS exhaust pipes, LS/RS front mufflers, LS/RS connector pipes, LS/RS rear mufflers, LS/RS tailpipes. Tailpipes will fit into the factory tips located in the bumper. These tips are not part of the package.
- For Series 75 and Commercial Chassis, this will not be a direct fit. We do not have all the patterns needed (in these model years) for Commercial Chassis or Series 75. If you have a 1952-56 Series 75 or Commercial Chassis we will supply you with a couple pieces of straight tubing. You will then need to modify the system to fit.
- If you have original pipes still on your 1952-56 Cadillac Series 75 or Commercial Chassis, please give us a call at 800-503-9428.
-
This listing covers 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, and 1974 Buick Wildcat, Electra, Electra 225, and LeSabre's with dual exhaust and 4 mufflers. For Buick Riviera's refer to 1963-74 Buick Riviera section. Excludes 1967-69 Buick LeSabre's which were stock from the factory with a single exhaust system only. Photo depicts the stock dual exhaust for 1972 Buick LeSabre's, Centurion's, Electra's, & Electra 225's with the stock V8 455ci.- Dual exhaust system includes LS/RS exhaust pipes, LS/RS front mufflers, LS/RS connector pipes, LS/RS rear mufflers with short tailpipes. Metal-to-metal connection at the manifolds, no gaskets required.
-
This listing covers model year 1956 Buick (only). Photos depicts the system for a 1956 Buick Special's & Century's- The dual exhaust system consists of LS/RS exhaust pipes, LS/RS mufflers, and LS/RS tailpipes. This is a metal to metal connection and does not require any gaskets. It is also flanged through out, so you will only need clamps to use in conjunction with any universal hangers you may order.
-
This listing covers model years 1933, 1934, 1935, 1936, 1937, 1938, 1939, 1940, 1941, 1942, 1943, 1944, 1945, 1945, 1947, 1948, and 1949 Dodge's with the stock 6 cyl engine. Photo depicts the system for a 1936 Dodge Coupe convertible.- Single exhaust system consists of the exhaust pipe, muffler, and tailpipe.
-
Our mufflers are a double walled shell. The end caps are roll-seamed. The outer wrap is smooth with no exposed welds. The baffles and end caps are a heavy gauge material.- Use this listing to build your own custom oval muffler. You tell us what you need and we will get it built for you. There will be no returns on custom built mufflers so be sure you triple check your measurements.
-
This listing cover model years 1950, 1951, 1952, 1953, 1954, 1955, 1956, 1957, 1958, and 1959 Chevy trucks with the stock 6 cyl. Photo depicts the system for MY's 1950-55 (MY 1955 1st Series) Chevy 3100 with the stock 6 cyl.- Single exhaust consists of the exhaust pipe, muffler, and tailpipe.
- Please specify the vehicle series through the checkout process.
-
This listing covers model years 1973, 1974, 1975, 1976, 1977, and 1978 Jeep Truck, Wagoneer, and Cherokee's with the stock V8. Photo depicts the stock single exhaust for 1978 Jeep Cherokee's & Wagoneer's with the stock V8 (customer opted to have tailpipe cut to reduce the shipping cost).- For MY's 1973-75 this single exhaust system consists of LS exhaust pipe, Y pipe, muffler, and tailpipe. Y pipe may be NORS.
- For MY's 1976-78 this single exhaust system consists of the Y pipe, muffler, and tailpipe. Y pipe may be NORS.
-
This listing covers model years 1975, 1976, 1977, and 1978 Mark IV and Mark V's. Photo depicts the dual cat-back system for a 1978 Mark V stock with converters on both manifolds. This photo was taken long ago and shows the resonator inlet pipe as a separate pc. We now have patterns for the LS/RS resonators and that pipe is now an integral part of the resonators.- Dual cat-back exhaust system consists of the H pipe (2 pc.), LS/RS mufflers, LS/RS connector pipes, and LS/RS resonators with tailpipe. Please be certain to specify if your Mark is stock with 1 or 2 cats during the check our process.
-
This listing covers model years 1972, 1973, and 1974 Torino's and Ranchero's stock with a V8 and dual exhaust. 1972-74's stock with the 429ci were stock with a single exhaust only. Photo depicts the stock dual exhaust for 1972 Torino's (exc. Ranchero & SW) with the stock 351C V8- Dual exhaust system consists of the H pipe, LS/RS mufflers, and LS/RS tailpipes. Chrome tips are not included. This system is a metal-to-metal connection at the manifolds and does not require gaskets.
-
This listing covers model years 1958, 1959, 1960, 1961, 1962, and 1963 Thunderbird's with the stock V8 and dual exhaust with 2 mufflers. This listing is the stock set up for 1962 Thunderbird's with a 6 bbl carburetor. For the stock set up 1962 Thunderbird's stock with a 4 bbl carburetor and for MY 1961 refer to 518725. If you have a 1961 and want to eliminate the resonator, this is the listing to be used. Photo depicts the dual exhaust system for 1963 Ford Thunderbirds with the stock V8- Dual exhaust system consists of the H pipe, LS/RS rear exhaust pipes, and LS/RS mufflers with tailpipes.
- MY 1963 will be asked to report the type of gasket needed (flat or donut) in the check out process.